• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window can be a nuisance. It can also be a chance to upgrade your glass to energy-efficient or insulated windows, and enjoy benefits such as more comfort, higher potential for resales, and less costs.

It's a task you can take on yourself for only a fraction of the cost of hiring an expert. It requires the right tools and an hour or two of your time.

Glass

Replace your single-paned windows with tempered insulation glass to improve the efficiency of your energy, reduce noise, and protect the historical integrity of your older home. Most homeowners with basic hand tools can repair windows with ease. Alongside a replacement window panes pane, the following tools are needed such as latex glazing putty; Glazier's points; pliers and the use of a heat gun to warm the old putty, if necessary. Before starting, put on gloves and safety goggles as working with broken glass can cause injuries.

Begin by removing any broken pieces of glass. It is recommended to use pliers, but a flathead can be used equally. Use a wood chisel, or putty knives, to take away any old putty remaining around the frame and the window sash. Be careful not to damage the window sash. Take your time and work slowly. This should be done on a ladder, not the ground. Also, ensure that someone below the sash hold it steady.

Make sure the window frame is ready to receive the new pane when you have removed the old glue. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of the width and height. These measurements can be sent to a home center or window Pane replacement hardware store to have an item cut from stock glass to the right size. You can cut the glass yourself if you have the appropriate tools.

After putting the new pane in place After installing the new pane, apply a small amount of caulking around the edges to ensure it is weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to secure the pane in its place. The points shouldn't be so tight that they cause friction between the frame and sash however they should not be loose.

Before applying the putty make sure to knead it until it's soft and free of lumps. Make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to another and ensure that it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of steel that allow glass to be secured into the window frame without causing damage to the delicate surface. Learning how to use these hidden tiny pieces of help is simple and can save you money on professional installation or the cost of purchasing new glass.

After taking off the old putty, glazier points as well as any remaining leftovers clean the frame thoroughly using an utility knife. If necessary it is necessary to lightly sand the wood along the rabbet grooves to smooth out rough areas. If you do sand the wood, be sure to protect it with painter's tape to avoid accidental damage.

Take the dimensions of the frame and write down accurate measurements. These dimensions can be taken to an hardware or home centers store, and the new pane will be cut to a smaller size. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane into the frame and press it into the frame by using your hands. Then, use the tip of your chisel or back of the putty knife to tap in the glazier's points, as illustrated in Figure 11. When you're done, they should be in line with the top edge of the pane and the raised shoulders of the points should be just below the rabbet's rim groove.

Apply a thin bead of glazing compound over the edges of the glass that has been made and into the rabbet grooves, to seal and protect them. Allow it to dry completely and cure.

Install the new window sash once the glazing compound has dried. First, coat the wood with a thick layer of linseed. This will prevent the new putty from drying out or cracking when it absorbs moisture. Apply this coat using a brush or the tip of your knife, then use the chisel or the back end of the knife to gently press the new sash and glazier's point into the rabbet grooves. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball thrown, a rock thrown in error, or a fallen tree can cause a broken or cracked window pane. The majority of windows can be replaced easily by installing a new piece. The glass is held in position by a small metal clip, referred to as a glazier's point and putty. This compound is also known as glazing compound. Before you install a new pane, first remove the old one and clean the area using the help of a rag, an abrasive scraper that is a pull type or a wood chisel. Wear gloves and safety glasses while working. You'll require a heat gun if the window is glued to the frame.

If you're planning to reinstall your original sash, you must remove the molding that holds the old pane. Then sand the sash to make sure it's flat and ready for a new caulk. After the sash has been re-installed, apply a new caulk made of silicone around the glass to ensure it won't leak or discolor in time.

Take out the glazing points in the rabbets. These are the grooves in the sash window replacement where the glass is. If they're difficult to cut out, try holding a hand tool like a heat gun to soften them first. If you're using a heated gun, make sure not to cause damage to the sash or its railings by using the tool too close.

Prepare the bed for your new pane by removing the old glaze points and putty. Roll a piece of glazing compound between your hands, and form it to be about 1/2-inch thick. Press it into the rabbets where the glass will be put. The glass should rest against the putty on both sides. If needed gently tap your glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If the crack isn't sealed, you'll need to use putty to keep water from getting in. Once the putty is dry, wipe the oily film off of the glass and allow it to dry completely before painting. If you paint before the putty has completely dry, it will not form an effective seal and could discolor or leak in time.

Paint

If you've had a broken window pane, then you may be concerned about the expense of a new one. But the truth is that replacing a single glass pane doesn't need to cost a fortune if you do it yourself. In fact windows with double panes can be replaced at a fraction of the cost of an expert.

First, if you're working on a large-sized window, make sure it is securely fastened to the frame. By using the correct tools and techniques to complete this task easily and quick.

When you're ready to start, begin by removing the old window by prying out the metal glazing points that are attached to it. These are tiny metal triangles that function as "nails" that hold the window within the frame. They are placed beneath a layer of glazing putty that is then cured to form a solid, molded wedge which holds the Window Panes Replacement in place and hides the points.

After you have the old pane taken away, clean up the surrounding frame and wood. Scrape off any old paint, and sand the rabbet grooves in which the glazing points were. These should be sanded to the point of being bare, so that you can paint them the same color as the rest of the frame. After the sanding process, apply a coat of flax oil to the wood's surface to help extend its lifespan.

Then, take measurements of the dimensions of the window's opening. It is necessary to take horizontal and vertical measurements of the entire opening as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you get the exact measurement for the new pane. This will allow for seasonal changes in the glass. Bring these measurements to a hardware or home improvement store, and they will have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.