• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, the wear and tear can cause lock malfunctions. There are a few easy steps you can follow to restore the security of your uPVC door.

These easy fixes will ensure your home is secure regardless of whether you re-align the lock or clean the locking mechanism.

Clean the Lock

Although emergency patio door repair doors are a great option to bring the outside in and keep the elements out however, they can also pose an issue for security in the event that your lock isn't operating as it should. With time, wear and tear, cold and hot weather dirt and debris can take their toll on the lock on your patio door and make it difficult to open. Fortunately, with some minor maintenance you can make sure that your patio door's locks always work effectively.

To begin with, it's important to clean the lock on your patio door repair service door and all the moving parts. This will help get rid of any grime or coatings that could be preventing your lock from working correctly. Start by wiping down all the moving parts of the lock for your patio door with a damp cloth, then make use of a scouring pad, or a rough damp cloth to scrub the hard-to-reach parts of the door and frame that are covered in dirt. It is recommended to wipe the entire lock using dry cloths to eliminate any remaining dampness and let it to air dry prior to applying it to the next time.

If your patio door uses pin-tumbler latches, you can lubricate it by applying powdered Graphite on the key. You can also use a Teflon lubricant such as WD-40 Multi-Use Product. This kind of lubricant is easy to apply and it doesn't dissolve over time. If you are unable to locate an appropriate lubricant you could try using a pencil with an extremely sharp tip. Insert the pencil into the lock and jiggle it around a bit to spread the graphite.

Tracks for sliding patio doors require regular maintenance to ensure they're free of dust, dirt and other debris. They are particularly susceptible to snow, ice and other particles, which could cause them to jam or bind. This could make it difficult for your patio door to be opened and closed.

Clean the track rails and rollers on sliding patio screen door repair doors by removing weather stripping that is dirty or damaged. Clean it, and then replace it. The same applies to patio door rollers which can be cleaned and then sprayed with a non-stick lubricant to help them move freely.

Lubricate the Moving Parts

uPVC french doors, like sliding patio doors, work with 3-4 or sometimes five-point locking mechanisms, which include the handle and lock cylinder controlled by keys. These doors require maintenance, the lubrication of moving parts. This can be done with a thin oil (never WD40) and is recommended to be done at least once per year.

If sagging hinges aren't a cause, the door may be skewed and catch or striking the strike plate hole within the frame. Remove the strike plate, and use a sharp tool to increase the size of its mortise. This will permit the latch to fit properly into the hole, and also prevent it from hitting the frame.

When the cylinder is out of the way take a measurement of its width using a book or piece of wood that can fit into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner dimension runs from the center of the adjustment screw until the end of the cylinder.

Check the width of the lock.

If your patio door latch is difficult to turn, even after cleaning and oiling it's possible that it's not aligned with the strike plate. Check if your door is in a balanced position, and if the hinge screws are in good condition. In a lot of instances, moving the strike plate upwards or downwards can fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to engage. In this situation, you'll need to enlarge the hole with either a hammer or chisel, and then test the latch to make sure that it is able to engage the strike plate smoothly without rubbing against or landing on the frame of the door jamb.

You should identify the type mortise lock you have before buying the replacement. You can do this by looking at the faceplate of the lock and determining if it is round or square. Then, look at the screw holes on the existing lock and note the size of each one. This will help you find a replacement that is the same width and will fit perfectly into the hole that you already have.

You'll need to identify the mortise lock and examine it for scratches, bends or other damage that requires to be repaired. A badly bent or damaged latch is more likely than one that's been used a lot to break. Replace the lock if it displays indications of damage.

After you've examined the lock and decided on the kind of replacement you require now is the time to start working on the actual repair. The old spindle and handle should be removed from the doorway to the patio. Install the new handle. Start by installing the inside handle. Align it with the spindle and then secure it into by using two bolts or screws. Install the exterior handle after the interior handle. After you've completed these steps you can test the new handles to ensure that they open and close easily and that the latch catches properly with the strike plate.

Make sure the door's strike is checked

The strike plate and door latch are two pieces that work together to lock the door. A misaligned strike plate or door latch will result in the latch not being able to latch the door in a proper manner. This is typically simple to solve.

First, inspect the holes in the strike plate's receiving to make sure they are clear of obstructions such as dirt or plastic plugs. Release the screws that hold the strike plate in position. This allows it to move vertically but it will not be able to separate from the frame. Then, adjust the strike plate until its holes for receiving are aligned with the latch hooks on the door latch. Once the strike plate has been adjusted, tighten all screws and test whether the door closes smoothly.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are crucial to lock and unlock your door. These metal plates are usually placed on the top and bottom of the door jamb, where they support the door's latch. The door latch slides onto the strike plate and forms a seal. If the strike plate is damaged or rusted or not properly installed the latch might not lock the door properly.

A misalignment of the strike plate and latch is one common cause for a patio lock to not close or remain in place. The easiest way to check for this is by performing the "lipstick test." Apply some lipstick on the edge of the deadbolt and put masking tape on it. The lipstick will leave a mark when you shut the door. This will reveal exactly where the latch meets the strike plate. If the mark is too low or high you can adjust the strike plate.

If your patio door locks for sliding aren't functioning properly they can help keep your home safe from burglars. You must repair the issue as soon as you can. By following these simple steps, you'll be able to fix your patio door's lock and regain its functionality in no time.